- 您现在的位置：买卖IC网 > Sheet目录324 > ER3-8M (TechTools)EMULATOR EPROM ECONOROM III 8MEG
Connect the Download Cable
Select an unused PRINTER port on your PC. Remove any “dongles”, security keys, printer switch boxes
or extension cables from the port. Plug the supplied download cable directly into the selected printer port.
Plug the other end of the cable into Econo ROM III’s “IN” port.
PLUGGING Econo ROM III INTO A SERIAL PORT
or an ETHERNET CABLE COULD DAMAGE THE
EMULATOR!
Connect Daisy-chain Cables
Multiple units are daisy-chained by connecting the “OUT” connector from one unit to the “IN” connector of
the next unit. Additional units are added in the same manner. Use the supplied 12” daisy-chain cable to
interconnect the units.
When daisy-chained together, the emulators automatically determine their position in the chain, making it
unnecessary to configure their addresses. However, it is important that you understand how their addresses
are determined.
The LAST EMULATOR in the chain (the one without a cable plugged into its “OUT” connector) is
always emulator #1 . The next emulator in the chain is #2 and so forth. The emulator closest to the PC
will always be the highest numbered emulator.
Run self-test
Running self-test immediately after installation gives you a solid baseline and helps you to find and correct
any errors early on. Self-test will verify proper installation of all drivers, proper operation of the parallel
port and all Econo ROM III functions except the target interface buffers.
You will find 16 and 32bit console mode programs in directories below your install directory. The 16bit
self test is included in case you plan to use the 16bit loader on a DOS machine. The 32bit self-test should
be used if you are planning to use the Windows Quickloader or the 32bit console mode loader. We
recommend using the 32bit self-test if you are running under Windows 95 or above.
If you are using multiple Econo ROM IIIs, we recommend that you test them collectively to ensure reliable
operation in the final configuration.
Type “ER3TEST32” to run a full speed test over printer port 0x378. You can change the printer port by
using a /P parameter. For example, if your emulator is connected to a printer port at 0x3bc, you would
enter “ER3TEST32 /P3BC”. The most common printer port addresses (in order of popularity) are 378,
278 and 3bc.
If any of these tests fail, refer to the troubleshooting section for assistance. If the troubleshooting section
does not resolve the problem, contact our technical support people for help.
Econo ROM III User’s Manual
7
Copyright ? 2000, TechTools
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ESF2424
FRAME SWING ECLIPSE 19.25X19"
ESF3024
FRAME SWING ECLIPSE 24.5X19"
ESF3624
FRAME SWING ECLIPSE 29.75X19"
ESP1212
PANEL STEEL SWING 12X12" WHT
ESP1612
PANEL STEEL SWING 16X12" WHT
ESP1616
PANEL STEEL SWING 16X16" WHT
ESP1620
PANEL STEEL SWING 16X20" WHT
ESP2016
PANEL STEEL SWING 20X16" WHT
相关代理商/技术参数
ER-3997
功能描述:烙铁 SOLDERING TIP
RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included
ER-3998
功能描述:烙铁 SOLDERING TIP
RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included
ER-3999
功能描述:烙铁 SOLDERING TIP
RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included
ER39R37CA
制造商:OMRON AUTOMATION AND SAFETY 功能描述:REFLECTOR FOR E3T
ER3A
制造商:TAYCHIPST 制造商全称:Shenzhen Taychipst Electronic Co., Ltd 功能描述:SURFACE MOUNT SUPER FAST RECTIFIERS
ER3A_04
制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:SURFACE MOUNT RECTIFIER
ER3A_06
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:3.0A SURFACE MOUNT GLASS PASSIVATED SUPERFAST DIODE
ER3A_07
制造商:DIOTEC 制造商全称:Diotec Semiconductor 功能描述:Superfast Switching Surface Mount Si-Diodes